Peugeot 3008 Key Fob Problems
The mid-sized SUV from Peugeot, the 3008, has lots of positive aspects. It's well-designed, it drives great and has a large boot. But can it beat off strong competition in perhaps the most crowded segment of the market?
If your Peugeot keyfob isn't working, it may have been exposed to clean or soapy tap water. It is possible to take off the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are powered by an e-cigarette size battery. This power is utilized to operate the remote locking system, as well as other features. This battery has a limited life span and may wear out over the course of years of usage. Testing the voltage is a simple method to determine if a battery is defective. Multimeters are used to measure voltage between the poles that are plus and minus of the battery. The results of this test will tell you whether the battery is dead or not.
The receiver module could be the cause of your key fobs not functioning after having used your Peugeot 3008 for a long time. The receiver module is in charge of receiving radio frequency signals transmitted by key fobs and sending them out to the car's systems. If the receiver module is damaged or damaged, it will not be able send commands to other modules inside the vehicle.
Another common reason for a key fob that is not working is moisture or sweat on the circuit board. It can trigger short circuits, which could drain the battery and stop the remote locking feature of the fob. If this is the case you must take your key fob in to a chip level technician to repair it.
Water damage
Whether you dropped your key fob into the pool, tossed it in the washing machine or even left it in the rain for too long, water damage can cause a lot of problems. Water is a good conductor, and it can cut off circuit boards. It can also cause corrosion to the metal traces on the key fob as well as other components. A wet circuit board can cause the battery to discharge its charge.
If you have an extra key fob, use it to lock or unlock your Peugeot 3008 to eliminate the possibility that a dead battery is the cause of the issue. Interference signals can also cause your key fob to cease working properly. These interfere with the signal sent by the receiver module. These interference signals are caused by many sources that include radio transmitters within the close vicinity.
If you hear sloshing noises emanating from your Peugeot 3008 when driving it could be due to a clogged condensate drain from the evaporator. You can test this by blowing compressed air through the drain holes in your door. You can also use flexible metal wire for wriggling drain holes to clean any dirt that has accumulated. Air pockets can be identified by sloshing sounds.
Receiver module that is defective
The receiver module in the receiver module of a Peugeot 3008 is responsible for transmitting the remote keyless signal from the keyfob into the receiver inside the car. The receiver module could be damaged and block the car from accepting your key fob. This issue can be caused by an inactive battery or water damage. Or, interference from electronic devices operating at the same frequency. In these cases the car might display the message "card not detected" on the display.
Fortunately, there are several options to solve this issue. Try replacing the battery or reprogram the key fob. You can also use a spare key in order to start the car. However, if your key fob isn't functioning after these steps, it may have a chip faulty.
The best way to determine whether your key fob has damaged chip is to take it off and clean it with paper towel and rubbing alcohol. If the chip is damaged, you need to purchase a new one. FB Series enclosures are designed for key fobs and come with an optional coin battery holder that can fit the most common type of key fob batteries. These enclosures can be customized by using digital printing and CNC-machined cutouts. If your key fob was exposed to salty or dirty tap water, the chip may be contaminated and requires to be cleaned.
G28 with malfunctions
If you receive the message "card not detected" this indicates that your car is unable to receive signals from your key fob. This can be caused by several reasons, such as the battery being weak or dead. In most cases, the issue will be resolved by pushing the start button using the key fob. In certain instances however, you might have to take the key fob to a Peugeot dealer for further repairs.
The first step to resolve a Peugeot 3008 key fob that doesn't open or lock the doors is to test its battery. Batteries are typically the cause of malfunctioning keys. However there are other factors that may be at play. These include worn buttons as well as water damage.
If you've recently been exposed to water and have your Peugeot key fob exposed to pure tap water, it's a good idea to remove the battery and dry the electronic components using paper towel. You can also use isopropyl alcohol or a cleaner for this purpose. If the fob has been exposed to salt or soapy water, it's best to replace it.
If your key fob isn't working You can reset it by removing the battery that is 12 volts for 15 minutes. Connect the negative cable, and then the positive cable.